Clarke CTS11 Manuale delle Istruzioni

1206Part Number 6500750Operating & MaintenanceInstructions10” TABLE SAWModel CTS11©10” TABLE SAWModel CTS11

10Crosscut A cutting operation made across the width of the workpiece - across thegrain.Featherboard A device which can help guide workpieces during r

11UNPACKING AND CHECKING CONTENTSThe Table Saw is shipped complete in one carton.Separate all parts from the packing materials and check to ensure tha

12ASSEMBLYIMPORTANT:Take great care to avoid contact with the saw teeth which are extremely sharpwhen performing the following operations.Handle1. Att

13Fig. 7Riving Knife1. Remove the table insert.2. Raise the blade as far as possible. You may find it helpful to adjust the blade angle, so that thebl

14Fitting The Blade Guard1. Raise the saw blade as far as possible.2. Attach the blade guard to the riving knife, asshown.• The guard should be secure

15Dust Outlet1. Connect a vacuum cleaner hose to the dustoutlet port on the rear of the table saw.Fig. 11

16MOUNTING THE SAWIMPORTANTIf the saw is to be a permanent fixture, ensure it is sited in an area with adequateillumination and power supply.DO NOT pl

17NOTE: For proper stability, holes must be counter sunk on the underside of the plywood so that screw headsare flush with the bottom surface of the m

18IMPORTANT CHECKS - BEFORE STARTINGIMPORTANT:Before attempting to use the machine, it is necessary to ensure the variouscomponents are correctly adju

19Overload Cut-OutYour machine also features an overload cut-out device, so that if the machine is overloaded (due tofeed pressure being too great, a

2

20Using The Mitre Gauge1. Slide the securing bolts into the slot on thefence as shown.2. Slide the mitre gauge assembly into one of theslots on the ta

21Adjusting The Rip Fence1. Lift the fence handle up.2. Slide the rip fence to the position you require.3. Push the fence handle down to lock into pla

22Fig. 21Fig. 20CUTTING METHODSRipping Or Rip CuttingRipping means to cut a piece of timber in the samedirection as the grain, i.e. usually lengthwise

23Cross cutting, with supportFig.27445mm44mm10mmAuxiliary Fence19mm120mmPush Stick And Push BlockMake the Push Block using pieces of 10mm plywoodand 1

24CROSSCUTTING TIPS1. Do not make cuts freehand (without using the mitre gauge or other auxiliary device) the blade maybind in the cut and cause kickb

25Fig. 30Fig. 29 Mitre CuttingMitre cutting is the term used for cutting at an angleother than 90O to the edge of the wood.1. Adjust the mitre gauge t

26MAINTENANCEWARNING! FOR YOUR OWN SAFETY, SWITCH MACHINE OFF AND REMOVE PLUG FROM POWER SOURCEBEFORE ADJUSTING, MAINTAINING OR LUBRICATING YOUR SAW.D

27Renewing Motor BrushesWARNING!ENSURE THE PLUG IS DISCONNECTED FROM THE POWER SUPPLY BEFORE PROCEEDING• Lower the blade to minimum height and remove

28 TROUBLE SHOOTINGTROUBLE PROBABLE CAUSE REMEDYSaw will not start 1. Saw not plugged in 1. Plug in the machine2. Fuse blown or circuit breaker 2.

29PARTS LISTSNo. Description Qty Part NoNo. Description Qty Part No1 Locking nut M6 4 HTCTS110012 Flat washer 39 HTCTS110023 Left board 1 HTCTS110034

3Thank you for purchasing your new CLARKE 10” TABLE SAW, which is designed for DIY, andhobby use ONLY.Before attempting to operate this machine, pleas

30For Spare Parts and Service, please contact your nearest dealer,or CLARKE International, on one of the following numbers.PARTS & SERVICE TEL: 02

31PARTS DIAGRAMFig.37

32

4SPECIFICATIONSModel No ...CTS11Part No...6500753Motor ...

5SAFETY INSTRUCTIONSKEEP WORK AREA CLEAN : Cluttered areas and benches invite injuries.CONSIDER WORK AREA ENVIRONMENT: Do not expose power tools to ra

6SAFETY INSTRUCTIONSUSE OUTDOOR EXTENSION LEADS: When the tool is used outdoors, use only extension leads intended foroutdoor use and so marked. Alway

7SAFETY INSTRUCTIONSUSE THE MITRE GAUGE: Always hold the work firmly against the mitre gauge fence when cross cutting.LOCK THE GUIDES: Always ensure t

8ELECTRICAL CONNECTIONSWARNING! THIS APPLIANCE MUST BE EARTHED.Connect the mains lead to a 230 volt (50Hz) domestic electrical supply via a standard 1

9FEATURESFig.1 1. The switch panel incorporates the ON and OFF switches. 2. A dust extraction port is provided at the rear of the machine. A vacuum ex