Clarke 250TE Specifiche Scaricare il pdf (Pagina 11)

PREPARATION OF THE WORKING AREA

The working area must be sufficiently spacious, not humid, and well-ventilated as

to avoid any fumes which develop from the welding process and from incidental

material adhering to the pieces to be welded (oils, paints, tars...) which may cause

annoyance to the operator.

Avoid welding by contact with humid parts nearby combustible liquids. Least of

all, do not weld upon tanks which may contain flammable residuals.

ADDITIONAL SAFETY PRECAUTIONS for MIG WELDING

✔ALWAYS ensure that there is full free air circulating around the outer casing of

the machine, and that the louvres are unobstructed.

✔Welding arc can seriously damage your eyes. Both operator and spectators

must ALWAYS use a proper welding face shield or helmet, with suitable filter

lenses. Proper gloves and working clothes should be worn at all times.

✔ALWAYS check that the pressure regulator and gauges (where fitted), are

working correctly. DO NOT lubricate the regulator.

✔ALWAYS use the correct regulator. Regulators are designed to be used with

a specific gases.

✔ALWAYS inspect the hose before use to ensure it is in good condition.

✔ALWAYS keep the free length of gas hose outside the work area.

✔ALWAYS remove all flammable materials from the welding area.

✔ALWAYS Keep fire extinguisher handy....’Dry Powder, C0

or BCF, NOT Water

✗ NEVER remove any of the panels unless the machine is disconnected from

the supply, AND never use the machine with any of the panels removed.

✗ NEVER attempt any electrical or mechanical repair unless your are a qualified

technician. If you have a problem with the machine contact your local

CLARKE dealer.

No. Description Part No.

PARTS LIST - MIG 130EN

Handle-extension Grip EM21600006

Handle-extension EM33725054

Wire Feeding Motor EM22810001

Complete Thermostat 100 + Support EM04600113

Plastic Handle EM21600021

Complete Fan EM04600055

Torch Grommet On Front Panel EM21690001

Welding Current Switch EM22200006

Potentiometer Knob EM21690017

Yellow Pilot-light Switch EM22200022

Access Panel Hinge EM21690178

Dividing Panel EM33720063

Wire Spool See Accessories

Fixed Spool Holder EM21690011

Spool Holder Retaining Ring EM21690012

Plastic Wire Feeders EM44400001

P.C. Board EM22710043

Cable Clamp EM21605010

Left Access Panel EM33705217

Front Panel EM33710165

Wheels-axle EM55200014

Right-side Upper Panel EM33705216

Rear Panel EM33715063

Wheel EM21625034

Wire Feed Roll Knurled EM33805001

Front Plastic Frame EM21690175

2 Pins Male Connector EM22105040

Male Connector EM22105042

Front Plastic Foot EM21610014

Inductance EM44135060

Rectifier EM22400049

Transformer EM44120049

Back Plastic Foot EM21610015

Earth Clamp EM22110005

Earth Cable EM43210108

Torch compl. EM23000049

Power Cable w/Plug +13A Fuse EM20220068

Back Plastic Frame EM21690176

Spool Holder Handwheel with Nut EM21800036

Lower Panel EM33700138

4 Lobes Hand-wheel EM21800051

Gas/No Gas Change Board EM21800050

Side Panel Clip EM21690177

Plastic Mask W/Handle EM21905018

Transparent Glass EM21905020

Dark Glass 82x108 BS DIN11 EM21905021

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 21 22

Commenti su questo manuale

Nessun commento

Clarke 250TE Specifiche Pagina 11

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi per la saldatura Clarke 250TE